diff options
| -rw-r--r-- | source/contemporary_unisex/leisurewear/index.rst | 10 | ||||
| -rw-r--r-- | source/contemporary_unisex/leisurewear/low_waste_bathrobe/index.rst | 93 |
2 files changed, 103 insertions, 0 deletions
diff --git a/source/contemporary_unisex/leisurewear/index.rst b/source/contemporary_unisex/leisurewear/index.rst new file mode 100644 index 0000000..a0c4938 --- /dev/null +++ b/source/contemporary_unisex/leisurewear/index.rst @@ -0,0 +1,10 @@ +************* + Leisurewear +************* + +.. toctree:: + :maxdepth: 2 + :caption: Contents: + + low_waste_bathrobe/index + diff --git a/source/contemporary_unisex/leisurewear/low_waste_bathrobe/index.rst b/source/contemporary_unisex/leisurewear/low_waste_bathrobe/index.rst new file mode 100644 index 0000000..d106e73 --- /dev/null +++ b/source/contemporary_unisex/leisurewear/low_waste_bathrobe/index.rst @@ -0,0 +1,93 @@ +Low Waste Bathrobe +================== + +.. figure:: + :align: center + +.. only:: html + + .. contents:: + + +Materials +--------- + +Fabric +^^^^^^ + +* About 2 m of towel material; +* 20 cm cotton jersey. + +Notions +^^^^^^^ + +* sewing thread to match the fabric. + +Pattern +------- + +Measurements +^^^^^^^^^^^^ + +You need to take the following measurements: + +``height_neck_back_to_knee`` (A18) + vertical distance from the back of the neck to the knee (or to where + you want the bathrobe to end); +``across_back_b`` (I08) + from armscye to armscye on the back; +``neck_back_to_waist_b`` (H19) + vertical distance from the back of the neck to the waist; +``shoulder_length`` (I01) + distance from the side of the neck to the tip of the shoulder; +``armscye_circ`` (L19) + circumference around the armscye. + +Pattern +^^^^^^^ + +Measure a rectangle as wide as the full width of the fabric and as high +as the desired length of the bathrobe (A18) plus 2 cm sewing allowance. + +Near the top, mark the quarter points, where you will cut the armscye +slits. From each quarter point, measure half ``across_back_b`` (I08) +towards the center back, and measure the position of the center back +seam, which should be ``neck_back_to_waist_b`` (H19) plus 2 cm long. +Mark two slits, 5 cm tall for the belt in the pleat fabric, parallel to +the seam at about 2 cm of distance, and aligned with the end of the +seam. + +For the sleeves, measure two rectangles as tall as half the width of the +fabric and as high as ``armscye_circ`` (L19) plus 4 cm allowance. + +For the belt, measure a rectangle as wide as the full width of the +fabric, and 10 cm long. + +Instructions +------------ + + +Cutting +^^^^^^^ + +Cut the rectangles described in the Pattern section; mark the position +of the armscye slits with a partial cut 5–10 cm long, but don't cut them +fully until you're ready to insert the sleeves. + +.. tip:: + + As long as the selvedges aren't horribly different from the fabric, + don't cut them away, but let them be part of the pattern pieces. + +Sewing +^^^^^^ + + + +Finishing +^^^^^^^^^ + + +Gallery +------- + |