From c0872e346ce4823941db2a2510571a09508e03d4 Mon Sep 17 00:00:00 2001 From: Elena ``of Valhalla'' Grandi Date: Fri, 10 Jun 2022 08:52:38 +0200 Subject: Pattern fixes --- .../shirts/1880_shirt/1880_shirt.val | 58 +++++++++++----------- .../shirts/1880_shirt/index.rst | 23 +++++---- 2 files changed, 41 insertions(+), 40 deletions(-) (limited to 'source') diff --git a/source/historical_menswear/shirts/1880_shirt/1880_shirt.val b/source/historical_menswear/shirts/1880_shirt/1880_shirt.val index e430c21..d66589b 100644 --- a/source/historical_menswear/shirts/1880_shirt/1880_shirt.val +++ b/source/historical_menswear/shirts/1880_shirt/1880_shirt.val @@ -36,7 +36,7 @@ treasury… - + @@ -95,7 +95,7 @@ treasury… - + @@ -323,14 +323,14 @@ treasury…
- + - - + + @@ -346,14 +346,14 @@ treasury… 66 - + - - + + @@ -372,21 +372,21 @@ treasury… - + - + - + - + 219 @@ -399,7 +399,7 @@ treasury… - + @@ -413,14 +413,14 @@ treasury… - - + + - - + + @@ -432,14 +432,14 @@ treasury… 135 - + - - + + @@ -453,14 +453,14 @@ treasury… 151 - + - - + + @@ -476,13 +476,13 @@ treasury… 171 - - + + - + @@ -491,15 +491,15 @@ treasury… - - + + - + diff --git a/source/historical_menswear/shirts/1880_shirt/index.rst b/source/historical_menswear/shirts/1880_shirt/index.rst index 6b81271..da03f2c 100644 --- a/source/historical_menswear/shirts/1880_shirt/index.rst +++ b/source/historical_menswear/shirts/1880_shirt/index.rst @@ -101,7 +101,8 @@ nicely on your fabric with as little waste as possible: a bit shorter (8-10 cm) than the back; ``shirt_width`` the flat width of the shirt: historically this would have been the - width of the fabric (something like 90 - 100 cm would be typical); + width of the fabric (something like 90 - 100 cm would be typical), + and today using half the width of the fabric (70-80 cm) can work fine; ``front_slit_length`` the length of the slit (and pleated part) in front: this can easily be as long as the ``neck_front_to_waist_f`` measurement @@ -203,9 +204,8 @@ Cut the full rectangles for the front and back. If you already have done a shirt in this size, and have the :ref:`paper pattern for the armscyes <1880_shirt-marking_armscyes:>`, mark the seam -lines on the front and back, and if you want cut them with single (for -the original felled seam) or double (for french seaming) seaming -allowance. +lines on the front and back, and if you want cut them with a double +seaming allowance. .. figure:: gri_33125012088023-770.svg :align: center @@ -467,13 +467,14 @@ towards the body. Rather than sewing and felling the sleeve as the original instructions suggested, you may get a neater result by french-seaming - it. Cut the shoulder piece with a double seaming allowance (this is - already marked in the valentina pattern), put the sleeve in with - wrong sides facing, backstitch at a bit less than the sewing - allowance from the edge, press; turn the sleeve inside out, right - sides facing, backstitch the straight part at a bit more than the - sewing allowance from the previous seam, turn it right side out and - hemstitch the gathered part catching each gather with a stitch. + it. Cut the shoulder piece with a double seaming allowance (if you + want to change it in the valentian pattern it's after point A and + before point A67) put the sleeve in with wrong sides facing, + backstitch at a bit less than the sewing allowance from the edge, + press; turn the sleeve inside out, right sides facing, backstitch the + straight part at a bit more than the sewing allowance from the + previous seam, turn it right side out and hemstitch the gathered part + catching each gather with a stitch. From the scraps of fabric cut two squares 5 cm wide, cut them in half on the diagonal, fold down their edges and sew them as small gussets to the -- cgit v1.2.3