From 178b098927b8f5cff30324374a4d46110cc992c8 Mon Sep 17 00:00:00 2001 From: Elena ``of Valhalla'' Grandi Date: Mon, 20 Jul 2015 16:22:16 +0200 Subject: makefile + basic slic3r conf. --- conf/basic.ini | 120 +++++++++++++++++++++++++++++++++++++++++++++++++++++++++ 1 file changed, 120 insertions(+) create mode 100644 conf/basic.ini (limited to 'conf/basic.ini') diff --git a/conf/basic.ini b/conf/basic.ini new file mode 100644 index 0000000..879b9a5 --- /dev/null +++ b/conf/basic.ini @@ -0,0 +1,120 @@ +# generated by Slic3r 1.1.7 on Mon Jul 20 16:03:26 2015 +avoid_crossing_perimeters = 1 +bed_size = 200,200 +bed_temperature = 0 +bottom_solid_layers = 3 +bridge_acceleration = 0 +bridge_fan_speed = 100 +bridge_flow_ratio = 1 +bridge_speed = 80 +brim_width = 0 +complete_objects = 0 +cooling = 1 +default_acceleration = 0 +disable_fan_first_layers = 1 +dont_support_bridges = 1 +duplicate_distance = 6 +end_gcode = M104 S0 ; turn off temperature\nG28 X0 ; home X axis\nM84 ; disable motors\n +external_perimeter_speed = 70% +external_perimeters_first = 0 +extra_perimeters = 1 +extruder_clearance_height = 20 +extruder_clearance_radius = 20 +extruder_offset = 0x0 +extrusion_axis = E +extrusion_multiplier = 1 +extrusion_width = 0 +fan_always_on = 0 +fan_below_layer_time = 60 +filament_diameter = 3 +fill_angle = 45 +fill_density = 40% +fill_pattern = honeycomb +first_layer_acceleration = 0 +first_layer_bed_temperature = 0 +first_layer_extrusion_width = 200% +first_layer_height = 0.25 +first_layer_speed = 40% +first_layer_temperature = 200 +g0 = 0 +gap_fill_speed = 20 +gcode_arcs = 0 +gcode_comments = 0 +gcode_flavor = reprap +infill_acceleration = 0 +infill_every_layers = 1 +infill_extruder = 1 +infill_extrusion_width = 0 +infill_first = 0 +infill_only_where_needed = 0 +infill_speed = 60 +interface_shells = 0 +layer_gcode = +layer_height = 0.25 +max_fan_speed = 100 +min_fan_speed = 35 +min_print_speed = 4 +min_skirt_length = 5 +notes = +nozzle_diameter = 0.5 +only_retract_when_crossing_perimeters = 1 +ooze_prevention = 0 +output_filename_format = [input_filename_base].gcode +overhangs = 1 +perimeter_acceleration = 0 +perimeter_extruder = 1 +perimeter_extrusion_width = 0 +perimeter_speed = 40 +perimeters = 3 +post_process = +print_center = 100,100 +raft_layers = 0 +resolution = 0 +retract_before_travel = 2 +retract_layer_change = 1 +retract_length = 2 +retract_length_toolchange = 10 +retract_lift = 0 +retract_restart_extra = 0 +retract_restart_extra_toolchange = 0 +retract_speed = 80 +seam_position = aligned +skirt_distance = 6 +skirt_height = 1 +skirts = 2 +slowdown_below_layer_time = 30 +small_perimeter_speed = 30 +solid_fill_pattern = rectilinear +solid_infill_below_area = 70 +solid_infill_every_layers = 0 +solid_infill_extrusion_width = 0 +solid_infill_speed = 40 +spiral_vase = 0 +standby_temperature_delta = -5 +start_gcode = G28 ; home all axes\nG1 Z5 F5000 ; lift nozzle\n +support_material = 0 +support_material_angle = 0 +support_material_enforce_layers = 0 +support_material_extruder = 1 +support_material_extrusion_width = 0 +support_material_interface_extruder = 1 +support_material_interface_layers = 3 +support_material_interface_spacing = 0 +support_material_interface_speed = 100% +support_material_pattern = pillars +support_material_spacing = 2.5 +support_material_speed = 60 +support_material_threshold = 0 +temperature = 190 +thin_walls = 1 +threads = 2 +toolchange_gcode = +top_infill_extrusion_width = 150% +top_solid_infill_speed = 30 +top_solid_layers = 5 +travel_speed = 130 +use_firmware_retraction = 0 +use_relative_e_distances = 0 +vibration_limit = 0 +wipe = 0 +z_offset = 0 -- cgit v1.2.3